When you usually install the door, you must think that the door stopper is a small thing, and you don't pay much attention to the installation, right?
In fact, although the door stopper is small, if it is not installed properly, it will not only affect the appearance of the home but also have a poor use effect.
Wooden door stopper installation method
1. Confirm the door stopper installation method
2. Test whether the door suction function is reasonable
3. Draw the positioning position of the door stopper
4. Drill the installation hole of the door suction
5. Assemble the fixed end of the door stopper
6. Fix the door on the ground
7. Confirm the position of the door stopper at the door end
8. Fine-tuning1. Confirm the door stopper installation method
1. Confirm the door stopper installation method
First of all, you must confirm with the owner the installation method of the wooden door stopper, whether it is installed on the ground or on the wall. After confirming the specific installation location, start to measure the size and how much space should be left behind the door
2. Test whether the door suction function is reasonable
The second step is to open the door to the required maximum position, test whether the function of the door stopper is reasonable and whether the distance between the door stopper and the door is suitable. Locate the position of the door. Whether to go in a little or come out a little, what is the specific angle of the door stopper?
After the final position is determined, locate on the floor tiles, first locate the stop position of the door, use a pencil to confirm the position of the door on the floor tiles, then confirm the final position of the door opening, and then confirm the final installation position of the door stopper.
3. Draw the positioning position of the door stopper
Mark the last position of the wooden door stopper. Why do you need to position it twice, both for the door and the door stopper, for better installation? The two points are in a straight line, which is the best way to confirm the angle of the door stopper and door opening.
4. Drill the installation hole of the door suction
Drill holes on the ground or wall according to the size of the door stopper.
5. Assemble the fixed end of the door stopper
Install the fixed end of the wooden door stopper and tighten the screws on it. The door stopper is divided into a fixed end and a fixed end. The screws need to be tightened before installation and then tightened to the ground or wall with the included inner corner wrench.
6. Fix the door on the ground
Tighten the screw with a small internal angle. This is a delicate job without experience. After confirming the position, drilling, and assembling, the next job is to install the fixed end on the ground and tighten the fixed end with the attached internal angle tool. The screw-wide suction is installed automatically.
7. Confirm the position of the door stopper at the door end
The suction end of the wooden door on the door only needs to be tightened with screws. The door absorbs light and is installed. The fixed end is still useless. Position the end suction with screws tight.
8. Fine-tuning1. Confirm the door stopper installation method
Fine-tune the angle of the fixed end of the wooden door stopper and then fully tighten it. The last step in the installation of the door stopper is to fine-tune, rotate the angle of the door stopper so that it fits perfectly with the door stopper at the door end, and finally tighten the screws thoroughly.
Summary: Door stoppers also need to pay attention to daily maintenance during use for long-term use.
When cleaning, try not to wet the metal-plated parts, first remove dust with a soft cloth or dry cotton yarn, and then wipe with a dry cloth to keep it dry. Do not use colored cleaners or forcefully damage the surface layer.
Author:Written by Ms.Rebecca Fu from S4A INDUSTRIAL CO.,LIMITED
Factory Address:Building S4A, South Third Lane, Qiuyuling Street, Zhangkeng Village, Hengli Town, Dongguan City, Guangdong Province Office Address:#601,floor 6 ,building 1,JINFANGHUA industrial zone, Bantian St. Longgang Dist. Shenzhen, PRC.
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.